Putting holes in plastic trim

Modified and aftermarket systems, lights, wiring, etc.

Moderator: F9K9

TexasBlaZeR2
Crew Elite
Crew Elite
Posts: 163
Joined: Sun Oct 09, 2005 3:07 pm
Location: Houston, TX

Putting holes in plastic trim

Post by TexasBlaZeR2 »

I need to add a hole of almost one inch in size to the trim panel I received from GM Parts direct. The plastic is about 1/16" thick and I do not want to mess it up. Who has experience doing this. What is the best way to go about cutting out the hole?
[size=75]Tom (Knight) Houston, TX
2005 BlazeR2 (still have)
2013 Avalanche LTZ (Z71 front end and flares/0
2000 BlaZeR2 (sold)
2006 Avalanche Z71 (sold)
User avatar
gocntry
Crew Elite
Crew Elite
Posts: 613
Joined: Wed Mar 31, 2004 2:14 pm
Location: Va

Post by gocntry »

Maybe A Hole Saw Would Be Your Best Bet?

Image
The Crew Is Gone, Now I Have A Hoe
TexasBlaZeR2
Crew Elite
Crew Elite
Posts: 163
Joined: Sun Oct 09, 2005 3:07 pm
Location: Houston, TX

Post by TexasBlaZeR2 »

Do they have those at Sears?
[size=75]Tom (Knight) Houston, TX
2005 BlazeR2 (still have)
2013 Avalanche LTZ (Z71 front end and flares/0
2000 BlaZeR2 (sold)
2006 Avalanche Z71 (sold)
User avatar
SONOMA915
Crew Elite
Crew Elite
Posts: 281
Joined: Thu Jun 16, 2005 8:56 am
Location: EL PASO TEXAS

Post by SONOMA915 »

I have had lots of success with uni bits. I am not sure if they sell one that goes up to an inch. You could start off with a small hole and work your way up to an inch. Just make sure you hold on to your drill and the part you are drilling.
[size=75]2004 GMC Sonoma ZR5 (Sold)
2005 Toyota Tacoma[/size]
User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Post by HenryJ »

Keep the hole saws cool when drilling metal or thick plastics. I squirt bottle with water helps, but requires three hands.
For metal you can wet a paper towel and stuff it inside the hole saw.
Your saws will last longer :mg:

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
Walt
Admin K Elite
Admin K Elite
Posts: 1556
Joined: Thu Jan 22, 2004 11:27 pm
Location: Mize, MS

Post by Walt »

HenryJ wrote:Keep the hole saws cool when drilling metal or thick plastics. I squirt bottle with water helps, but requires three hands.
For metal you can wet a paper towel and stuff it inside the hole saw.
Your saws will last longer :mg:
Good advice. You can also turn the hole saw in reverse (actually put the drill in reverse). Sometimes this can give you a cleaner cut on soft surfaces.
--Walt
2001 S-10 CrewCab - Retired...
User avatar
adrenalnjunky
Crew Elite
Crew Elite
Posts: 895
Joined: Sun Jul 27, 2003 11:32 am
Location: West Monroe, Louisiana
Contact:

Post by adrenalnjunky »

I bought a big unibit at a specialty tool warehouse - was not cheap, but it's a great tool to own.

Not sure how big mine is -- I think it goes up to 3/4" - I used it in my bodylift if I remember correctly.

You need Irwin Unibit part # 10220 - it starts at 1/2" and goes up to 1"

Unibit Link
[size=75]Thanks, CHRIS
2000 S10 Blazer 4x4 4Dr. -- 2" PA BodyLift, Daystar Shackles, TB Crank, 1.75" Rear wheel spacers, Yakima roofrack, 30" BFG AT's.
1969 VW Bug -- airbagged and in pieces.
1962 VW Karmann ghia -- rusting over in the corner. "That's not a tool--that's a damn brick!"[/size]
TexasBlaZeR2
Crew Elite
Crew Elite
Posts: 163
Joined: Sun Oct 09, 2005 3:07 pm
Location: Houston, TX

Post by TexasBlaZeR2 »

Here is what I bought today. The hole was miked at 7/8". I got a bit that looks like a wood bit, but has threads on the center part. It was only 4 bucks at Sears.

I think this should do the trick. What do you guys think?

drill bit for aux hole
[size=75]Tom (Knight) Houston, TX
2005 BlazeR2 (still have)
2013 Avalanche LTZ (Z71 front end and flares/0
2000 BlaZeR2 (sold)
2006 Avalanche Z71 (sold)
User avatar
04crewvt
Crew K Elite
Crew K Elite
Posts: 1465
Joined: Sat Oct 22, 2005 8:24 am
Location: St Albans Vermont
Contact:

Post by 04crewvt »

I personally wouldn't use that on plastic. I have cut automotive grade plastic for custom radio installs before and used a hole saw like gocntry suggested above with good luck. You don't need to buy a whole set if you don't want to ,your local hardware store should sell just the mandril and bit separately but you will pay more that way than if you get the kit and once you have it you will wonder how you got along without it.
When cutting I backed the plastic with a wood block so it couldn't deform and used slow speed on drill so the plastic wouldn't melt or burn.
[size=75]Why does the universe decree that if you have all the time in the world to work on projects you have no money and vice versa?
Green 2004 ZR-5 w/ too much to list here: http://www.cardomain.com/ride/2296465[/size]
User avatar
kauaibuilt47
Crew
Crew
Posts: 69
Joined: Mon Aug 22, 2005 10:50 pm
Location: Yelm, WA
Contact:

Post by kauaibuilt47 »

Probably not the best way to do it but....

i used my dremel with the sandpaper barrel on my crotchrockets side fairings. it melted the plastic rather than cut but it went perfectly. looks/feels smooth and stock and i could form it exactly the way i needed to.

again, probably not the best method but it worked.
[size=75]Never get into an argument with an idiot. They only bring you down to their level and then beat you with experience.[/size]