SPAL Fans, what size fuse???

Modified and aftermarket systems, lights, wiring, etc.

Moderator: F9K9

User avatar
Rockrz
Crew Elite
Crew Elite
Posts: 414
Joined: Sat Nov 17, 2007 7:18 am
Location: Texas

SPAL Fans, what size fuse???

Post by Rockrz »

What size fuse are you guys using on your electric fans?

I'm using a 30 amp and it blows about every 4 to 6 months for some reason.

Should I go with a 35 amp, or maybe switch to some sort of breaker switch?
User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Post by HenryJ »

What fans are you using?

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
Rockrz
Crew Elite
Crew Elite
Posts: 414
Joined: Sat Nov 17, 2007 7:18 am
Location: Texas

Post by Rockrz »

SPAL dual electric fans

If I remember right, the reason I was using a 30 amp fuse was because that is what they recommended.

I thought about going to a heavy duty fuse holder that will accept the 30 amp fuse as far as physical size is concerned...but is designed to handle much larger fuses and amps.

When it blows, it melts the fuse holder on one side so it may be that the fuse holder is too small for the amperage.
User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Post by HenryJ »

Consult the wiring size tables. Make sure you are using the correct size wire.
Consider splitting the supply for them if you are drawing more amperage than is reasonable for one wire.

Make sure your system is capable of maintaining the voltage with out a large drop. That can create heating in a motor.

Usually a bigger fuse is not the answer. The problem lies elsewhere.

There have been some SPAL fan failures. That might be a possibility too.

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
Rockrz
Crew Elite
Crew Elite
Posts: 414
Joined: Sat Nov 17, 2007 7:18 am
Location: Texas

Post by Rockrz »

Maybe I need to go with larger wires, but I am using the same size wires that SPAL uses coming out of the motors so one would think this would be OK.

Seems like the wires would be damaged by excessive heat if they were too small, right? Wouldn't they get all stiff and discolored?

So far the wire themselves don't apear to be harmed at all, and the fans continue to work just fine.

It's only popped the fuse twice in about a year.
User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Post by HenryJ »

If you add length, you must increase the size. The heat will always build at the weakest link. While the wire may not be getting hot to the touch or so it is visible, the resistance will increase.

Poor connections can be a problem too. Make sure they are all clean and a little dielectric grease is na good idea.

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
Rockrz
Crew Elite
Crew Elite
Posts: 414
Joined: Sat Nov 17, 2007 7:18 am
Location: Texas

Post by Rockrz »

OK, I guess it wouldn't hurt to go with a larger wire size.

What about lithium grease?
I've always heard that's how many connectors are lubed at the factory.

Also, is it possible to use a 30amp breaker switch instead of an inline fuse?
Or would that not be a good idea...
User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Post by HenryJ »

Do not use lithium grease. Dielectric silicone is designed for this.

A manually resettable breaker might be just fine. I would not use an auto resetting breaker , if there is a problem it will get really hot.

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
raven2510
Crew Elite
Crew Elite
Posts: 115
Joined: Wed Feb 20, 2008 4:35 pm
Location: Omaha, Nebraska

Post by raven2510 »

idk....but to me dual spal efans are gonna be using more than 30 amps...especially on start up
1999 Chevy S10 ZR2
User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Post by HenryJ »

I agree. The quick jump on start usually won't blow the fuse. Fuses blow slowly, relatively speaking. It takes more time than starts usually offer in this situation.

If they recommend 30 amps , that is probably as much as I would run, just to be within their recommendations. That covers you if there is a fan meltdown.

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
Rockrz
Crew Elite
Crew Elite
Posts: 414
Joined: Sat Nov 17, 2007 7:18 am
Location: Texas

Post by Rockrz »

So, what guage wire are you guys using with the Taurus eFan?