Ignition Coil - any Performance gains???

Modified and aftermarket systems, lights, wiring, etc.

Moderator: F9K9

User avatar
Rockrz
Crew Elite
Crew Elite
Posts: 414
Joined: Sat Nov 17, 2007 7:18 am
Location: Texas

Ignition Coil - any Performance gains???

Post by Rockrz »

Are there any noticable and/or worth while performance gains
by using performance ignition modules for the 4.3L?

If there are, anybody know what brand
(and part number) works best?
[size=75]I'm drivin a...2003 Chevy S10 Ex Cab LS 2WD, Auto, 4.3L, Vin Code X[/size]
User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Post by HenryJ »

Are you referring to the ignition module specifically? Or a capacitive discharge controller (ignition box)?

I have not seen aftermarket ignition modules used on our trucks.

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
Rockrz
Crew Elite
Crew Elite
Posts: 414
Joined: Sat Nov 17, 2007 7:18 am
Location: Texas

Post by Rockrz »

I was thinking of the coil I guess you'd call it where the
ignition wire from the dist cap connect to.

I'm hearing from other sources that the stock ignition
setup is pretty stout as is, so if there's aren't any
power gains to speak of then I'll leave it stock.

I have thought about this several times
but just now remembered to post the question
[size=75]I'm drivin a...2003 Chevy S10 Ex Cab LS 2WD, Auto, 4.3L, Vin Code X[/size]
User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Post by HenryJ »

Stock is pretty good. They do weaken with age. There are a few aftermarket replacements available at the same or even less cost than a stock replacement. They offer better output too.
Performance gains may not be very noticeable, but every little bit helps.
Not sure I would invest in it as a performance gain, but when replacement time comes I would upgrade.

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
Rockrz
Crew Elite
Crew Elite
Posts: 414
Joined: Sat Nov 17, 2007 7:18 am
Location: Texas

Post by Rockrz »

I always like to change many of my electronic parts
before they crap out on me and leave me stranded,
so when do you think is a good time to consider
replacing this?

My truck is an '03 with about 86k on it now.
[size=75]I'm drivin a...2003 Chevy S10 Ex Cab LS 2WD, Auto, 4.3L, Vin Code X[/size]
User avatar
killian96ss
Crew K Elite
Crew K Elite
Posts: 2669
Joined: Tue Sep 09, 2003 11:53 am
Location: Sacramento, California

Post by killian96ss »

There is no actual mileage when a coil will fail or should be replaced. There are plenty of vehicles still around these days that are 40+ years old and still using the factory coil.

When and if your coil does fail or if you just want a more efficient higher output coil, the Accel coil is the best replacement available right now. The factory coil is rated @ 38k volts, the MSD coil 40k volts, and the Accel coil is 48k volts.

Steve
User avatar
Rockrz
Crew Elite
Crew Elite
Posts: 414
Joined: Sat Nov 17, 2007 7:18 am
Location: Texas

Post by Rockrz »

killian96ss wrote:the Accel coil is the best replacement available right now
Would you happen to know the
part number for the Accel coil?

And, wouldn't the same part mumber apply to
all 4.3L V6 engines from late 90s forward?
[size=75]I'm drivin a...2003 Chevy S10 Ex Cab LS 2WD, Auto, 4.3L, Vin Code X[/size]
User avatar
crew cab sonoma
Crew Elite
Crew Elite
Posts: 238
Joined: Wed Aug 25, 2004 2:21 am
Location: Chattanooga, TN

Post by crew cab sonoma »

maximum rated voltage output is one of the least important
aspects to consider for a new coil...

for a 5000 rpm 6 cyl., its hard to improve on the stock coil...
[size=75]Lee

01 Sonoma Crew Cab 2.21 60ft. 10.24 @ 66.5 mph (1/8mi.)(SOLD)
00 Sonoma Ext. Cab 4WD. front axle removed, Torsen diff. W4M pcm. 2.10 60ft. 9.64 @ 71.0 mph (1/8 mi.)[/size]
User avatar
killian96ss
Crew K Elite
Crew K Elite
Posts: 2669
Joined: Tue Sep 09, 2003 11:53 am
Location: Sacramento, California

Post by killian96ss »

Rockrz wrote:Would you happen to know the
part number for the Accel coil?

And, wouldn't the same part mumber apply to
all 4.3L V6 engines from late 90s forward?
The Accel part # for 96 and later S10's is 140024.

Here is one @ Summit Racing.

95 and earlier S10's use a different coil with 2 connectors instead of 1.
crew cab sonoma wrote:maximum rated voltage output is one of the least important
aspects to consider for a new coil...

for a 5000 rpm 6 cyl., its hard to improve on the stock coil...
Aftermarket coils are more efficient due to their higher turns ratios, lower resistance, higher milliamp output, faster rise time, and they offer higher voltage "which is important" if you like faster starts, smoother idle, improved throttle response, and better high rpm performance. :wink:

Steve
User avatar
crew cab sonoma
Crew Elite
Crew Elite
Posts: 238
Joined: Wed Aug 25, 2004 2:21 am
Location: Chattanooga, TN

Post by crew cab sonoma »

the coil will only produce the ammount of voltage absolutely
necessary to to do the job, regardless of what the coil is capable of.
and the truth is, that the stock coil never has to approach its maximum
voltage potential. not during startup, cruise, or at WOT at 5000 rpm.
and certainly not at idle...

sorry about the delayed reply, i just happened back across this thread. :wink:
[size=75]Lee

01 Sonoma Crew Cab 2.21 60ft. 10.24 @ 66.5 mph (1/8mi.)(SOLD)
00 Sonoma Ext. Cab 4WD. front axle removed, Torsen diff. W4M pcm. 2.10 60ft. 9.64 @ 71.0 mph (1/8 mi.)[/size]